Making your trip with Chatham Area Transit!

Combining your biking or walking trip with public transit can help make your trip more successful. Chatham Area Transit offers a lot of options to extend your trip and help you go the distance.

All of CAT’s fixed-route buses are equipped with bike racks so you can take your bike with you at no extra cost. No special passes or training are required, and each rack can hold up to two conventional bicycles so they are available on a first-come, first-serve basis.

Learn more about using the bike rack on the front of CAT buses by visiting their website.

Want to plan your route, but you’re not sure where your closest stop is located — or where the route goes? Check out the CAT Tracker to view stops near you and see up to the minute information on when the next bus is going to arrive.

Extend your route downtown — for free! Thanks to a partnership with the City of Savannah, CAT operates a free downtown transit system spanning land and water.

While biking downtown might be easy, it’s a little difficult to get across the Savannah River! The Savannah Belles Ferry system provides free passage across the River between the riverwalk and Hutchinson Island from 7 a.m. to 10 p.m. seven days a week, and bikes are allowed.

As always, make sure to follow our biking and walking tips to make your trip as safe as possible

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Halloween Safety Tips

Everyone loves a good scare on Halloween, but we also want it to be a treat! Whether you’re out with your little ghosts, goblins and vampires or heading out on your own adventure, below are steps you can take to make sure the little trick-or-treaters make it home ok.

On average, children are more than twice as likely to be hit by a car and killed on Halloween than on any other day of the year. More kids out on our streets = more opportunities for potential collisions.

Below are our top tips for Halloween Safety:

  • Adults, join kids under age 12 for trick-or-treating. For older kids, make sure they have a designated route, time/place to meet up, and a cell phone to get in touch if needed.
  • Carry glow sticks or flashlights, use reflective tape or stickers on costumes, shoes and bags, and wear lighter colors (if possible) to help kids see and be seen by drivers.
  • Remind kids to cross the street at corners or crosswalks wherever possible. Look left, right and left again when crossing and keep looking as you cross.
  • Always walk on sidewalks or paths. If there are no sidewalks, walk facing traffic as far to the left as possible.
  • When selecting a costume, make sure it is the right size to prevent trips and falls. Try out all pieces of a costume before Halloween to make sure your kid can move freely. And choose face paint over masks when possible, as masks can limit children’s vision.
  • Remove tripping hazards to keep your home safe for visiting trick-or-treaters. Check outdoor lights and replace burned-out bulbs, and sweep any leaves from sidewalks and steps.

Driving Tips:

  • Drivers – slow down and be alert! Turn on headlights earlier in the day to spot kids from further away.
  • Avoid driving through densely populated neighborhoods between 5-9 pm (or if you do, be prepared for delays.) Many neighborhoods post trick or treating maps which may help you plan your route.
  • Avoid any distractions. Even if you’re using hands free devices, avoid any phone calls and lower your music/drive with windows down if possible when in neighborhoods.
  • Take extra time to look for kids at intersections, on medians, and at curbs.
  • Enter and exit driveways and lanes slowly and carefully.
  • Wait behind other vehicles that are pulled over – do not go around. They may be dropping off a group of children who could be coming out on both sides of the vehicle.
  • If you’re partying, stay sober or find another ride home.

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

How to Cross Railroad Tracks on a Bike

If you ride your bike in downtown Savannah, you’ve definitely come across some railroad tracks! Here’s how to cross them safely so your ride continues without a hitch.

  1. Slow down and come to a complete stop if the crossing is un-signalized.
  2. If the crossing is signalized, reduce your speed and still look both ways.
  3. Always cross at a 90 degree angle. Make sure your tires run perpendicular with the tracks.
  4. Take extra precaution when the tracks are wet, as there is less traction for your wheels.
  5. While crossing, stand on your bike pedals out of the saddle. Keep them level (feet at three and nine on the clock) as you smoothly coast across the tracks and keep your knees and elbows loosely bent — it’ll help you keep your balance and absorb shock.
  6. Never cross when the lights are flashing and the arm is down, or if you see a train coming. Railroad lights and the arm are designed for your safety.

Small tires — like on bicycles, wheelchairs, skateboards or skates – can become stuck when in-street tracks are crossed at too low an

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Get ready for your ride with the ABC Quick Check!

A is for Air

Make sure your tires are inflated to the pressure listed on the side of the tire

When your tires are correctly inflated, use your thumb to gently push on the outside edge and feel the pressure. This will help you quickly gauge if you need air in the future!

Check for damage on your tire and replace if it is too worn

B is for Brakes

Inspect your brake pads for wear, replace if there is less than 1/4″ of pad left

Check pad adjustment and make sure they don’t rub the tire

Look to see that you can fit your thumb between the brake lever and handlebar when the brakes are squeezed all the way — this means they’re properly adjusted

C is for Cranks and Chain

Pull on your cranks/pedals away from the bike — if they are loose, tighten the bolt.

Check that your chain is free of rust, gunk and any debris

Quick is for Quick Releases

Make sure all your quick release levers are closed (check your wheels and seat!)

They should all be pointing down and towards the back of your bike, so they don’t get caught on anything.

And then CHECK it all over!

Take a quick roll around to make sure everything is working properly, and if you’re carrying any cargo that you’re well balanced.

More of a visual learner? Check out this video from our friends at the League of American Bicyclists:

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

What to do if you’re in a crash

If you have the misfortune of being involved in a crash, it can be overwhelming and you may not know what to do. When your blood is pumping, your mind is racing, and you may be injured, the last thing you want to do is have to Google what to do. Below are our steps for the best actions to take after a collision.

Before we start, we always recommend carrying your cell phone, ID, a listed emergency contact, and something to write with/on in case your phone is broken. A bracelet like a RoadID can provide your information, emergency contacts and allergy information if needed.

  1. Do not immediately move – you may be more injured than you think. 
  2. Dial 911. Request the police and an ambulance to your location. 
  3. Leave your bike in the same state it was after the crash. Take pictures of the scene, including your bike, any damage to yourself, damage to the motor vehicle, and license plate number.
  4. Obtain the contact information of any witnesses.
  5. Always wait for the police to arrive and file an official report.
  6. Get the business card of the officer. Write your report number on the card in addition to getting a copy.
  7. Immediately seek medical attention. When in doubt, go to the ER! 
  8. Never negotiate with the driver of the vehicle at the scene of the crash, regardless of who may be at fault. Get the driver’s name and their insurance and contact information, along with the names and contacts of any passengers. You may discover additional injuries or destruction to property after the crash.
  9. Make no statement to insurance until you talk to a lawyer. 

Involved in a crash or want to report a close call? Submit your report on our website.

Data collected from the Close Call form can help us and agency partners assess potential conflict points and the frequency of near misses (or unreported crashes) involving bicyclists, pedestrians and motor vehicle drivers. Bicycle and pedestrian related crashes are under reported and this offers another way to address persistent issues. 

If you have encountered a dangerous road hazard call 311 or visit our Report Hazards and Issues page. In an emergency, please call 911.

Riding bikes comes with risks — like all vehicles. If you have been in a crash involving a bicycle and aren’t sure where to begin, contact the Law Offices of Joseph J. Steffen, Jr. for a free consultation.

Joseph J. Steffen Jr is an avid cyclist who specializes in local bicycle law, and serves on the board of Bike Walk Savannah. His focus and passion is for safe cycling for you and your family here in the Southeast, knowing the challenges of working with police officers on their reports, and picking an unbiased jury panel at trial that will understand a cyclists right to SHARE THE ROAD.

Visit joesteffen.com/bicycle-law for more information.

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Driving Safely around People Biking

Savannah’s level topography, dense urban form, and warm weather make it a great place to get around by bike. However, Savannah also has a high rate of traffic crashes involving people on bikes.

Tips for Safe Driving Near Bicyclists

React to bicyclists as you would any other vehicle. You wouldn’t drive inches next to another car, so why would you drive so close to a person on a bike?

Don’t park in bike lanes or blocking access to multiuse paths. It may just be “for a minute”, but that minute could be the difference in someone biking safely to their destination and being put in unnecessary conflict with another driver.

If there is oncoming traffic, slow down and wait to pass until traffic clears.

  • Check for bicyclists in your blind spots
  • When driving a larger vehicle, allow extra room for mirrors, extended wheel wells, trailers, etc.
  • Large profile vehicles can create a windblast, which can knock a bicyclist off the road
  • Return to your lane when the bicyclist is in your rearview mirror
  • Do not attempt to “squeeze by”

Do not past a bicyclist before a red light or stop sign, hill, or immediately before you make a right turn.

Give at least 3 feet of space! According to the updated 3 ft to pass law, updated July 2021:

  • A driver passing a person on a bike should change lanes if road and traffic conditions allow
    • Includes allowance to pass on a double yellow when conditions are safe to do so
    • No passing into blind turns, blind hills, or oncoming traffic
  • When it is not safe to change lanes, a driver is required to slow down to 25 mph or 10 mph below the posted speed limit, whichever is greater, to execute a safe pass within the lane and shared space
  • Violations of the law carry a maximum fine of $250 as a misdemeanor offense
  • Under Georgia law, a video recording of an act is valid as a witness for enforcement of violations

Don’t drive distracted or under the influence. Again, it’s the law!

Consider driving conditions. Whether it’s raining or sunny, there’s something happening that can influence your driving. Make sure to slow down or give yourself extra room if you need it, and consider pulling over rather than powering through if conditions are dangerous.

Avoid illegal courtesies, like encouraging someone to ride through a stop sign in front of you. They may be able to see further down the street than you, or may take more time to get rolling, which can cause everyone to get frustrated.

Know where kids are biking. Children may not know the rules of the road so slow down and pay extra attention when driving in areas where children can be expected.

Interested in learning more about being a Bicycle and Pedestrian Friendly Driver? Sign up for an upcoming class or view our webinar here!

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Signaling & Scanning

Signaling

  • Left Turn: Fully extend your left arm out to the side.
  • Right Turn: Fully extend your right arm out to the side or bend your left arm up at a right angle with your hand flat. Both are legal signals, and depend on your level of comfort with which arm you use.
  • Slowing or Stopping: Extend your left arm at a right angle with your hand open and pointing down towards the ground.

Scanning

Scanning is the act of looking over your shoulder, and is a key part of riding anywhere. It helps communicate your intentions to others and also shows you what is happening behind or around you.

Pro Tip: It may be difficult to scan and maintain a straight line while riding. Start by practicing scanning on a stationary bike to see your range of motion. You may want to purchase a mirror to help if you have limited range. Once you start practicing on a moving bike, if you have trouble maintaining a straight line you may want to try removing your hand (from the direction you are scanning) from the handlebars and place it on your lower back. This helps prevent your body from fully turning and pulling the handlebars. And make sure to keep peddling while scanning!

Scanning should be used in conjunction with signaling — you should scan before any turn and before making any signal.

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Plan Your Route

Whether you’re commuting to work or school, getting some exercise, or riding to get your groceries, planning your route can be a difficult — but necessary — step. You don’t want to get to your destination and realize you have to cross a six-lane highway in order to get there, but you also don’t want to ride down a cul-de-sac and not be able to get out. Below are our tips on how to plan your perfect route.

Try planning out your own bike route this May!

Mapping Out a Safe Route

Use Google Maps

Google Maps has come a long way in helping plan bike routes! Visit Google Maps, click Layers at the bottom of your screen, and then click Biking to show trails, dedicated lanes, bicycle-friendly roads and dirt or unpaved trails.

You can input your starting point and destination and select biking, which will suggest routes that follow bike infrastructure or bike-friendly streets, if available. You can even select street view in order to see a photo of the street, which can help you in quickly identifying if that’s a route you’d like to take. Pro Tip: Under Layers click Traffic, which can help you identify if streets are closed or if traffic is moving slowly in certain areas. Also, the wider the street the more cars are likely to be on it — and moving quickly!

Use Strava, Map My Ride or Ride with GPS

The great thing about biking in Savannah is that we have a lot of people out biking with you! There’s a pretty good chance that someone has a route similar to the one you’re looking to create, which means that websites like Strava, Map My Ride or Ride with GPS can help you find a route that someone has already ridden. They can also have heat maps, which can show you where people are riding.

Image © Bikabout

Tips for Planning Your Route

Maybe you can find a route digitally, but you’re concerned about riding it in person. You don’t have to dive all in right away!

  • Talk with other bike riders: Check out local biking groups on social media or in person and ask for some tips! Check out Bike Walk Savannah’s events for some more details on our rides.
  • Scout the route: If your route is on streets and not on bike paths, try it out in your car first. While you won’t be able to get exactly the same feel for the road, you can easily see if there are areas that are blocked off, high volumes of other cars, or might not have a safe crossing for you to use.
  • Experiment with your route: If you know the area well enough, take some time to experiment with different possible routes. Make sure to leave around the same time you would be biking to or from your destination, but give yourself some extra time (like on your day off). This can help you find additional streets that might be a little more comfortable for you.
  • Be familiar with your map: What happens if the street you usually take is closed due to construction or a crash? Do you know what other streets you can take? We recommend knowing a few different alternate routes, as well as knowing what sections you can’t swap out. This can also be helpful for different times of day — maybe you go to work taking one route, but return home on another.
  • Don’t be afraid to go multi-modal: Maybe you can’t ride directly from your house, but you can pick up some safe
  • streets a mile or two away. Check out Chatham Area Transit and see if there’s a bus you can take for part of your trip!

Need some more help? Request some bike route assistance from the BWS team or check out our routes page.

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Driving Safely around People Walking

It’s important to remember that we’re all people — and at some point in the day, everyone is a pedestrian.

Unfortunately pedestrian injuries and fatalities remain high, especially in Savannah. When you maintain safe speeds and practice other safe driving behaviors, our streets are safer for everyone!

Most at Risk

  • Seniors 65+
  • Kids ages 5-9
  • People under the influence

You never know who may cross your path unexpectedly, so by taking steps to be prepared and constantly paying attention, you can make sure everyone gets from where they are to where they need to be safely — including you!

Tips for how to avoid crashes involving pedestrians:

Know where people are. Does the street you’re on have sidewalks and activated crosswalks, or are people going to be forced to walk in the street or cross unexpectedly? Are there bus stops?

Do not pass stopped school buses. It’s not only the law, but stopped school buses create opportunities where kids or adults may be unexpectedly entering the roadway.

Slow down for crosswalks, regardless of if there are pedestrians. When you approach, give right-of-way to pedestrians who are waiting or in the crosswalk. Stop far enough away to indicate your intent. Scan the street before turning, as there may be someone waiting to cross on the street you’re turning onto. And remember, any intersection — whether marked or unmarked — is a space where pedestrians are legally allowed to cross.

Practice driveway safety. When we’re leaving our home or coming home is a very dangerous time for drivers. You may be distracted by opening your garage door, putting on your seatbelt, remembering your coffee, and might not be looking for kids or people walking behind your vehicle. Make sure to pay attention! Similarly, be aware when you’re in parking lots and pulling in or out of spaces.

Don’t drive distracted or under the influence. Again, it’s the law!

Consider driving conditions. Whether it’s raining or sunny, there’s something happening that can influence your driving. Make sure to slow down or give yourself extra room if you need it, and consider pulling over rather than powering through if conditions are dangerous.

Stay alert for pedestrians who may need more space. Did you notice that the street may not have sidewalks or ramps to get on those sidewalks? Do you see a pedestrian using a mobility device like a motorized wheelchair or cane, or maybe a family with small children? Make sure to give them some extra room!

Ultimately, SLOW DOWN.

Interested in learning more about being a Bicycle and Pedestrian Friendly Driver? Sign up for an upcoming class or view our webinar here!

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.

Sharing the trail

  • Be courteous & know the rules of the trail you are using.
  • Give a clear, audible signal when passing — bells or your voice are great!
  • Be cautious and yield to crossing traffic.
  • Stay to the right.
  • If you’re moving faster than the people in front of you, slow and wait for an opportunity to pass — don’t thread the needle.
  • Always be predictable — ride in a straight line, don’t weave across the trail.
  • Stay on the designated path.
  • Travel at a speed that allows you to watch for hazards as well as your surroundings.
  • Don’t blast your music. If you’re listening on headphones, make sure you can hear your surroundings or use one earbud.
  • Yield to more vulnerable path users. Bicyclists and skaters yield to pedestrians, pedestrians yield to those with young children or assistive devices.
  • If you’re riding in a group, move to a single file to allow oncoming traffic to pass.
  • If you are riding or walking while it is dark, be sure to use lights.
  • If you’re on the trail with your dog, make sure to keep it on a short leash. Retractable leashes are not recommended, as they can cause cuts and burns to both pets and people.
  • Keep it clean — whatever you bring in, bring out! If you notice a lot of trash or debris, call 311 or come out for a trail cleanup!

Our friends at The League of American Bicyclists have put together a great video overview below.

Learn more tips on our Resources Page.

This blog post is produced thanks to support from the Governor’s Office of Highway Safety.